design

Showing posts with label sewing. Show all posts
Showing posts with label sewing. Show all posts

Saturday 10 December 2011

Organza Ribbon flower

Well I must say that I do seem to be on a roll as far as these ribbon flowers are concerned and this is the latest. Ribbon and button offer.
What you will have in this tutorial is the basis bow that will allow you to build up lots more bows. I've kept this simple for you so I hope that you're ready to play along.

You won't need much to make this, just:

1.5 metres of 23mm ribbon. ( The wider the ribbon, the fuller the flower. If you use thinner ribbon you will need to wrap it more to get the fullness. All will become clear).
1 large button
a scrap of contrasting ribbon
thread
needle
1 piece of still cardboard 5cm x 15cm. ( Cut it off an old cardboard box).


To make the flower:

Start with cut piece of ribbon at the top of the card as seen.

Wrap the ribbon around the cardboard overlapping the pieces as you go. Tie a good knot in your thread ( don't worry as it's not going to be seen) and sew a running stitch along the bottom edge of the ribbon.


 Slide the ribbon off the cardboard.
 Pull the thread abd it will ruffle up the ribbon.

When you've pulled tight you can sew the two edges together at the back of the flower and open out the loops. Now you can leave it like this if you like.
 Or you can.....Cut the tops off the loops at a diagonal as shown.
Thread the scrap ribbon through the button and tie tightly. Sew in place in the center of your flower.
Do you like it?
Now I've put an offer on the Craft Fairy home site as usual so that you can get this ribbon at a lower price.
Click here for the offer.

Friday 13 May 2011

Vintage twisted ribbon roses

I've noticed that these twisted roses are appearing on many cards and sewing projects lately so I thought that I would bring you all a project and a video on how to do them. I've used fairly bright, well, very bright ribbon to make them as they can be shabby chic, but they can also be vivid and fashionable.

What You’ll Need:

Ribbon – at least 16mm wide

The one that I used here is the 23mm wide swiss dot grosgrain.

16mm satin ribbon in willow

a needle and thread
Cut a length of ribbon, about 30 to 45cm long. The longer (and wider) your ribbon, the larger your rose will be.
Tie a knot at one end of the ribbon, this will be the center of the rose.

Knot the end of the thread and secure it to the base of the knot.

Start twisting your ribbon and stitch it into place around the knot.

Carry on twisting the ribbon and sew it onto the rose that is developing.
Below is what it should look like from the front at this stage.
Keep on twisting and sewing until you have the size of rose that you want.

Once all the ribbon is wound up and secured, tuck the ends underneath and sew them into place with a few small stitchesKnot your thread, trim it, and you’re done
Now for the leaves. They are really simple too.

Take a length of the green satin ribbon and sew along one edge as shown. The longer the length the bigger the leaf. As a rule of thumb, your ribbon should be about two and a half times the width of the finished rose.
Pull the thread gently until you have gathered the ribbon as shown below.Stitch the ribbon together along the middle and then stitch it to the back of your rose and there you have it. Now you can make a card or far better brighten up a jumper or a hat.

Saturday 7 May 2011

Folded ribbon rose tutorial

A couple of weeks ago I asked if your 'could guess what it is yet?' I thought that I could get on and make a tutorial straight away but I have been so busy that it has taken me until now to do a very straight forward tutorial. So I've decided that I will put you out of your misery straight away, by showing you that the tutorial will be for a folded ribbon rose. The title of the post rather gave it away though. As I told you before you will need the shocking pink 23mm wide grosgrain for this and I used the swiss dot one as I wanted to have the contrast between the plain side and the dotty side. You can make a plain one if you want to but this looks kind of cute.



You will need to start by rolling a short section of the ribbon and securing it with a couple of stitches. Stitching is better than gluing as it will held in place and then, if you want to put it on a garment you can wash it without being afraid that it will fall apart. This roll will be your bud.


Next fold the ribbon at a 90 degree angle to the roll as shown below.Roll the ribbon around the central bud until you get to the end of the folded part. It will be obvious when you do it. Secure the bottom with a couple of stitches. ,Fold and roll again and again. See below. Make sure to put in a couple of stitches as you go.Below is what your rose should look like after you have folded a few times.Now look at the back and you will see how this is coming along, and where to put the stitching. Basically you keep on going until you have as many petals as you want. The cut you r ribbon and tuck the raw wdge under and tack into place. Turn over and your ribbon is done.


Tuesday 3 May 2011

Pincushion for a competition

Today, I'm posting a set of instructions to make a pincushion. I am making this as I am going to enter it for a WI competition in the summer. So. as I was going to do it for this, I thought that I might as well do the instructions and blog it as well. Being in posession of a huge choice of ribbons I really had no choice but to use them. All the ribbons that you see here are available from craftfairy.co.uk


Here is the finished cushion. I know that it is really girly and over the top kitch but who cares. I thought that if I was going to go for a domestic goddess kind of thing I might as well go over the top. 1950's at least. I even feel a frilly apron coming on. Perhaps not today though.


So. if you want to make something like this you will need to do some ribbon weaving first. This really is a good way to use up your scraps too as it only requires short lengths. the sort that are usually too short to be used for anything else.
Cut yourself a piece of fuisable interfacing about 2cm larger than the finished size of the pinchshion. E.g. if your pinchshion is to be 50cm x 50cm then cut your square 51cm x 51cm. I used a lightweight interfacing as I wanted the finished cushion to be soft not stiff.


Put the interfacing on the ironing board, fuisable side up. If your don't do it this way your will fuse it to the board. Lay your ribbons out in a pattern and pin to the ironing board over the interfacing.
Cut your lengths of ribbon so that they extend beyond the size of the backing fabric. You will trim them later so don't worry about being too precise. I used a mixture of widths and patterns but to keep the design looking good I used only three harmonizing colours. Pink, blue and a touch of white in the pattern. Lay them vertically over the interfacing.

Now weave the same pattern of ribbon in the horizontal direction as shown.

You should end up with what you see below. Push the ribbons together so that there are no gaps showing and pin in place. You will need to do this or the ribbon will move when you iron it.

Cover the ribbon weaving with a cloth and press with the iron. Do not use steam. This will create enough adhesion to allow you to flip the ribbon weave over and then press again to cause a better adhesion and create your fabric. See below. Now, flip the fabric over, and iron from the back. This will ensure that the ribbons stick to the interfacing really well.

Now, take a length of sewing thread with a knot in one side and sew a running stitch along one edge of the ribbon very close to the edge. When you have reached the end pull the thread to gather it to approximately the length of your 4 sides combined. 40 cm in my case. Secure the end of the thread.

Pin to the right side of the edge of the ribbon fabric. Tack the ribbon in place very near the edge. You will not reallt have a seam allowance on the ribbon. No need to have one really as the ribbon has a sewn edge should not frey. There will be a seam allowance on the ribbon fabric though.

Cut a piece of backing fabric that is the same size as the interfacing. I used a little broiderie anglais that I had in my scraps basket. With right sides together and the ribbon in the middle like a sandwich sew around three sided of the pincushion. I did this by hand as it really is too fiddly to even contemplate sewing on the machine.

When you have done this turn the pincushion around to the right side and fill with kapok or any other stuffing that you have. I had some left over from goodness knows when. Sew the last side into place from the back of the cushion and you have done.